Ethernet crossover cable

From Wikipedia, the free encyclopedia

Jump to: navigation, search

This article needs additional citations for verification. Please help improve this article by adding citations to reliable sources. Unsourced material may be challenged and removed. (June 2011)

Gigabit T568B crossover cable ends

An Ethernet crossover cable is a type of Ethernet cable used to connect computing devices together directly. Normal straight through or patch cables were used to connect from a host network interface controller (a computer or similar device) to a network switch, hub or router. A cable with connections that "cross over" was used to connect two devices of the same type: two hosts or two switches to each other. Owing to the inclusion of Auto-MDIX capability, modern implementations of the Ethernet over twisted pair standards usually no longer require the use of crossover cables.

Contents  [hide]  1 Overview 2 Crossover cable pinouts 3 Automatic crossover 4 See also 5 References 6 External links

[edit] Overview

8P8C modular crossover adapter

The 10BASE-T and 100BASE-TX Ethernet standards use one wire pair for transmission in each direction. By convention, one wire of the pair is designated "+" and the other "-". Following traditional telephone terminology, the + signal from each pair connects to the tip conductor, and the - signal is connected to the ring conductor. This requires that the transmit pair of each device be connected to the receive pair of the device on the other end. When a terminal device is connected to a switch or hub, this crossover is done internally in the switch or hub. A standard straight through cable is used for this purpose where each pin of the connector on one end is connected to the corresponding pin on the other connector.

One network interface controller may be connected directly to another without the use of a switch or hub, but in that case the crossover must be done externally in the cable or modular crossover adapter in a manner similar to how the null modem was used to directly connect two teleprinters. Since 10BASE-T and 100BASE-TX use pairs 2 and 3, these two pairs must be swapped in the cable. This is a crossover cable. A crossover cable was also used to connect two hubs or two switches on their upstream ports .

Because the only difference between the T568A and T568B pin/pair assignments are that pairs 2 and 3 are swapped, a crossover cable may be envisioned as a cable with one modular connector following T568A and the other T568B (see Jack crossover wiring). Such a cable will work for 10BASE-T or 100BASE-TX. Gigabit Ethernet (and an early Fast Ethernet variant, 100BASE-T4) use all four pairs and also requires the other two pairs (1 and 4) to be swapped. This meant common crossover cables available in the retail market were usually not compatible with the Gigabit Ethernet convention, but newer crossover cables could be made that worked for all speeds. The polarity of each pair is not swapped, but the pairs crossed as a unit: the two wires within each pair are not crossed.^[1]

[edit] Crossover cable pinouts

Crossover cable connecting two MDI ports

In practice, it does not matter if non-crossover Ethernet cables are wired as T568A or T568B, just so long as both ends follow the same wiring format. Typical commercially available "pre-wired" cables can follow either format depending the manufacturer. What this means is that one manufacturer's cables are wired one way and another's the other way, yet both are correct and will work. In either case, T568A or T568B, a normal (un-crossed) cable will have both ends wired according to the layout in the Connection 1 column.

Although the Gigabit crossover is defined in the Gigabit Ethernet standard^[2], in practice all Gigabit PHYs feature an auto-MDIX capability and are designed for compatibility with the existing 100BASE-TX crossovers. The IEEE-specified Gigabit crossover is generally seen as unnecessary.

Certain equipment or installations, including those in which phone and/or power are mixed with data in the same cable, may require that the "non-data" pairs 1 and 4 (pins 4, 5, 7 and 8) remain un-crossed.

Two pairs crossed, two pairs uncrossed
10BASE-T or 100BASE-TX crossover

Pin	Connection 1: T568A			Connection 2: T568B			Pins on plug face
	signal	pair	color	signal	pair	color
1	BI_DA+	3	white/green stripe	BI_DB+	2	white/orange stripe
2	BI_DA-	3	green solid	BI_DB-	2	orange solid
3	BI_DB+	2	white/orange stripe	BI_DA+	3	white/green stripe
4		1	blue solid		1	blue solid
5		1	white/blue stripe		1	white/blue stripe
6	BI_DB-	2	orange solid	BI_DA-	3	green solid
7		4	white/brown stripe		4	white/brown stripe
8		4	brown solid		4	brown solid

Gigabit T568A crossover
All four pairs crossed
10BASE-T, 100BASE-TX, 100BASE-T4 or 1000BASE-T crossover (shown as T568A)

Pin	Connection 1: T568A			Connection 2: T568A Crossed			Pins on plug face
	signal	pair	color	signal	pair	color
1	BI_DA+	3	white/green stripe	BI_DB+	2	white/orange stripe
2	BI_DA-	3	green solid	BI_DB-	2	orange solid
3	BI_DB+	2	white/orange stripe	BI_DA+	3	white/green stripe
4	BI_DC+	1	blue solid	BI_DD+	4	white/brown stripe
5	BI_DC-	1	white/blue stripe	BI_DD-	4	brown solid
6	BI_DB-	2	orange solid	BI_DA-	3	green solid
7	BI_DD+	4	white/brown stripe	BI_DC+	1	blue solid
8	BI_DD-	4	brown solid	BI_DC-	1	white/blue stripe

Gigabit T568B crossover
All four pairs crossed
10BASE-T, 100BASE-TX, 100BASE-T4 or 1000BASE-T crossover (shown as T568B)

Pin	Connection 1: T568B			Connection 2: T568B Crossed			Pins on plug face
	signal	pair	color	signal	pair	color
1	BI_DA+	2	white/orange stripe	BI_DB+	3	white/green stripe
2	BI_DA-	2	orange solid	BI_DB-	3	green solid
3	BI_DB+	3	white/green stripe	BI_DA+	2	white/orange stripe
4	BI_DC+	1	blue solid	BI_DD+	4	white/brown stripe
5	BI_DC-	1	white/blue stripe	BI_DD-	4	brown solid
6	BI_DB-	3	green solid	BI_DA-	2	orange solid
7	BI_DD+	4	white/brown stripe	BI_DC+	1	blue solid
8	BI_DD-	4	brown solid	BI_DC-	1	white/blue stripe

[edit] Automatic crossover

Main article: Auto-MDIX

Introduced in 1998, this made the distinction between uplink and normal ports and manual selector switches on older hubs and switches obsolete.^[3] If one or both of two connected devices has the automatic MDI/MDI-X configuration feature there is no need for crossover cables.

Although Auto-MDIX was specified as an optional feature in the 1000BASE-T standard^[2], in practice it is implemented widely on most interfaces. It has been available for example on Apple Inc. computers since about the Power Mac G5.^[4]

Besides the eventually agreed upon Automatic MDI/MDI-X, this feature may also be referred to by various vendor-specific terms including: Auto uplink and trade, Universal Cable Recognition and Auto Sensing.